- I had a similar problem. Water was spilled on a MacBook Air (2015 I think), after drying for a few days, it turned back on, but the keyboard and trackpad were not working properly. They were working, just intermittently. I took the laptop apart, and removed the trackpad cable. There was a small amount of corrosion on one end of the connectors.
- If the trackpad still doesn't click, even after removing the battery, try adjusting the screw shown on the following picture. You'll need a T6 torx screwdriver for that. Turning the screw counterclockwise will loosen the trackpad. Turning it clockwise will tighten the trackpad.
Macbook pro early 2015 13', I take a hit, after a few minutes turn off the screen and no longer starts. The backlight worked, and even the mac itself (connected in hdmi with another screen worked perfectly) then I open the case, I see all the connections and the mac worked again well I NOTE however that the trackpad no longer gives me the 'Click'. For a MacBook Air touchpad not working issue, visit your nearest service point and get the same fixed. When it comes to iPhone screen repair you must choose only the best and reliable service provider. Rapid Repair assures you quick and prompt service, unique door-step delivery together with a stand-by-device. Nov 20, 2020 Shut down your MacBook Press down and hold these keys on your keyboard – Control, Option, Shift Hold these keys down for 7 seconds and then press the power button while still holding Control, Option, and Shift. Hold down all 4 of these keys for another 7 seconds.
In this guide I show how to replace failed trackpad on a MacBook Air 13-inch or 11-inch laptop. Chrome app macbook.
In my case the trackpad started working erratically. The cursor was jumping all over the screen and moving on its own even if the trackpad wasn't touched.
TIP: if your trackpad stopped clicking, check the battery. It's likely the battery is swollen and blocking the trackpad from moving freely. If the trackpad clicks properly with the battery removed, you'll have to replace the battery.
New replacement trackpads available here.
Best free anti malware software for mac. STEP 1.
Place the laptop upside down and remove ten P5 Pentalobe screws securing the bottom cover.
Remove the cover.
NOTE: two screws I marked with yellow circles are longer than screws marked with red circles.
STEP 2.
Pull the battery cable out of the connector on the logic board.
STEP 3.
Remove five T5 Torx screws securing the battery. Three screws on the top (yellow circles) are longer that two screws on the bottom (red circles).
Remove the battery.
STEP 4.
Now you can access the trackpad.
In the following steps I'll show how to disconnect the trackpad cable (red arrow) and keyboard cable which is hidden (yellow arrow).
STEP 5.
On the following picture the trackpad cable connector shown in the locked state.
Open up the connector by lifting up the locking tab. You can use tweezers or your fingernail.
The locking tab will open up at a 90 degree angle.
Carefully pull the trackpad cable out of the connector.
STEP 6.
The keyboard plugs in into the connector which is hidden under the flex cable.
On the following picture the keyboard connector shown in the locked state.
Open up the connector by lifting up the black tab in the shown direction. You can use tweezers for that.
Pull the keyboard cable out of the connector.
STEP 7.
When all cables are disconnected, we can start removing the trackpad.
Remove six screws securing brackets to the laptop case.
You will need a very fine PH00 Phillips screwdriver.
Start separating the trackpad from the laptop case.
Remove the trackpad. Now it's ready for the replacement.
STEP 8.
It's likely that your new trackpad will not have metal brackets installed.
In this case you'll have to transfer them from the old one. Each bracket is secured by three screws.
STEP 9.
Start installing the new trackpad. Best female voice changer software. Position the lower side (red arrow) first.
Macbook Air Touchpad Click Not Working Lenovo
STEP 10.
Install only two screws but do not tighten them completely.
Macbook Pro Click Not Working
STEP 11.
Adjust position of the trackpad. Make sure it's seated evenly and gaps on each side are equal.
After that you can tighten the brackets and install remaining four screws.
TIP: if the trackpad doesn't click properly, you can try adjusting the screw. In most cases it's not necessary.
STEP 12.
Insert the keyboard cable back into the connector.
There is a white line on the keyboard cable. Make sure the cable goes all the way down into the connector and the white line levels with the connector.
Close the locking tab (yellow arrow).
Finally, connect the trackpad cable back in place and assemble the laptop.
